How to Deploy Openstack on RHEL6 using Foreman

From FedoraProject

(Difference between revisions)
Jump to: navigation, search
m (Parameters)
m (SELinux)
(20 intermediate revisions by one user not shown)
Line 120: Line 120:
 
rpm -Uvh http://download.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-8.noarch.rpm
 
rpm -Uvh http://download.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-8.noarch.rpm
 
yum-config-manager --enable rhel-6-server-optional-rpms --enable epel --enable puppetlabs-products --enable puppetlabs-deps
 
yum-config-manager --enable rhel-6-server-optional-rpms --enable epel --enable puppetlabs-products --enable puppetlabs-deps
yum clean all
+
yum clean expire-cache
 
</pre>
 
</pre>
  
Line 146: Line 146:
 
<pre>
 
<pre>
 
SELINUX = permissive
 
SELINUX = permissive
SELINUXTYPE=targeted
+
SELINUXTYPE = targeted
 
</pre>
 
</pre>
  
Line 222: Line 222:
 
Before starting, make sure the "RHEL Core: Common definitions" described earlier have been applied.
 
Before starting, make sure the "RHEL Core: Common definitions" described earlier have been applied.
  
If you have several interfaces activated, we need to specify which one the Foreman HTTPS server is going to use, so you can either:
+
In case there are several network interfaces on the Management machine, Foreman HTTPS service is to be activated on the desired interface by either:
* Deactivate all interfaces but the one you'd like the service to be running from. Be careful not to cut yourself out!
+
* Deactivate all interfaces but the desired one. Be careful not to cut yourself out!
 
or
 
or
* After the installation, replace with your IP of choice the "<VirtualHost IP:80>" and "<VirtualHost IP:443>" records in /etc/httpd/conf.d/foreman.conf file
+
* After the installation, replace with IP of choice the "<VirtualHost IP:80>" and "<VirtualHost IP:443>" records in the /etc/httpd/conf.d/foreman.conf file
  
Using Puppet itself onto the Management machine we install the Foreman suite:
+
Using Puppet itself onto the Management machine to install the Foreman suite:
  
 
<pre>
 
<pre>
Line 259: Line 259:
 
* Declare hostgroups   
 
* Declare hostgroups   
  
Those steps have mostly been scripted using Foreman API.
+
Those steps have been scripted using Foreman API.
  
{{admon/note|Note|The following process could also be done using Foreman GUI which is described here:
+
{{admon/note|Important|The script must be run (for now) from the Management server itself, as root}}
[[How_to_Deploy_Openstack_Setup_Foreman_on_RHEL6_manually]]}}
+
  
Prepare and download the script:
+
Download the script:
 
<pre>
 
<pre>
 
git clone https://github.com/gildub/foremanopenstack-setup /tmp/setup-foreman
 
git clone https://github.com/gildub/foremanopenstack-setup /tmp/setup-foreman
Line 270: Line 269:
 
</pre>
 
</pre>
  
Then edit the foreman-params.json to adjust it to your environment and needs by changing:
+
Then edit foreman-params.json file to and change the following to needs:
 
* The host section with your foreman hostname and user/passwd if you have changed them
 
* The host section with your foreman hostname and user/passwd if you have changed them
 
* The proxy name can be anything you'd like, the host is the same as foreman FQDN name, with ssl and port 8443.
 
* The proxy name can be anything you'd like, the host is the same as foreman FQDN name, with ssl and port 8443.
* The globals are your OpenStack values, adjust passwords and tokens
+
* The globals are your OpenStack values, adjust all passwords, tokens, network ranges and NICs values to you needs.
  
 
Notes: Be careful with JSON syntax - It doesn't like a colon at the wrong place!  
 
Notes: Be careful with JSON syntax - It doesn't like a colon at the wrong place!  
  
== Smart-Proxy ==
+
Lets launch the script to configure Foreman with our parameters:
 
+
Once Foreman-proxy and Foreman services are up and running, we need to link them together.
+
 
+
 
<pre>
 
<pre>
./foreman-setup proxy
+
./foreman-setup.rb -l logfile all
 
</pre>
 
</pre>
  
== OpenStack Puppet Modules ==
+
Check the log file to confirm there wasn't any error.
  
We need to download and import the Puppet modules for deploying and configuring Opentstack components.
+
{{admon/note|Note|The above process can also be done manually using Foreman GUI, it's described here:
The modules are sourced from the github project.
+
[[How_to_Deploy_Openstack_Setup_Foreman_on_RHEL6_manually]]}}
 
+
All OpenStack components are available from those modules:
+
<pre>
+
git clone --recursive https://github.com/gildub/puppet-openstack.git /etc/puppet/modules/production
+
</pre>
+
 
+
The nova-compute, nova-controller and other (to be described soon) installers:
+
<pre>
+
git clone https://bitbucket.org/gildub/trystack.git /etc/puppet/modules/production/trystack
+
</pre>
+
 
+
We need to import the Puppet modules into Foreman.
+
 
+
The import can be done from CLI or either Foreman GUI:
+
* Command line:
+
<pre>
+
cd /usr/share/foreman && rake puppet:import:puppet_classes RAILS_ENV=production
+
</pre>
+
 
+
{{admon/note|Note|To use with scripts, you can add the “batch” option to the rake import command:
+
<pre>rake puppet:import:puppet_classes[batch]</pre>
+
}}
+
 
+
 
+
* The GUI: Select “More -> Configuration -> Puppet classes” and click “Import from <your_smart_proxy>” button:
+
 
+
[[File:Foreman-import.png|400px]]
+
 
+
== Parameters ==
+
 
+
We provide all the parameters required by the OpenStack puppet modules in order to configure the different components with those values.
+
 
+
<pre>
+
./foreman-setup.rb globals
+
</pre>
+
 
+
== Hosts Groups ==
+
Host Groups are an easy way to group Puppet class modules and parameters. A host, when attached to a Host Group automatically inherits those definitions.
+
We manage the two OpenStack types of server using Foreman Host Groups.
+
 
+
So, we need to create two Host Groups:
+
* OpenStack-Controller
+
* OpenStack Compute Nodes
+
 
+
<pre>
+
foreman-setup hostgroups
+
</pre>
+
  
 
= Manage Hosts =
 
= Manage Hosts =

Revision as of 06:27, 26 April 2013

This Wiki provides the Open Source and Red Hat communities with a guide to deploy OpenStack infrastructures using Puppet/Foreman system management solution.

We are describing how to deploy and provision the management system itself and how to use it to deploy OpenStack Controller and OpenStack Compute nodes.

Note.png
Note
This information has been gathered from real OpenStack lab tests using the latest data available at the time of writing.


Contents

Introduction

Assumptions

  • Upstream OpenStack based on Folsom (2012.2) from EPEL6
  • The Operating System is Red Hat Enterprise Linux - RHEL6.4+. All machines (Virtual or Physical) have been provisioned with a base RHEL6 system and up to date.
  • The system management is based on Foreman 1.1 from the Foreman Yum Repo and Puppet 2.6.17 from the Extra Packages for Enterprise Linux 6 (EPEL6)/
  • Foreman provides full system provisioning, meanwhile this is not covered here, at least for now.
  • Foreman Smart-proxy runs on the same host as Foreman. Please adjust accordingly if running on a separate host.
Note.png
Conventions
  • All the code examples unless specified otherwise, are to be run as root
  • The URL provided must be replaced with corresponding host name of the targeted environment

Definitions

Name Description
Host Group Foreman definition grouping environment, Puppet Classes and variables

together to be inherited by hosts.

OpenStack Controller node Server with all OpenStack modules to manage OpenStack Compute nodes
OpenStack Compute node Server OpenStack Nova Compute and Nova Network modules providing OpenStack Cloud Instances
RHEL Core Base Operation System installed with standard RHEL packages and specific configuration required by all systems (or hosts)

Architecture

The idea is to have a Management system to be able to quickly deploy OpenStack Controllers or OpenStack Compute nodes.

OpenStack Components

An Openstack Controller Server regroups the following OpenStack modules:

  • OpenStack Nova Keystone, the identity server
  • OpenStack Nova Glance, the image repository
  • OpenStack Nova Scheduler
  • OpenStack Nova Horizon, the dashboard
  • OpenStack Nova API
  • QPID the AMQP Messaging Broker
  • Mysql backend
  • An OpenStack-Compute

An OpenStack Compute consists of the following modules:

  • OpenStack Nova Compute
  • OpenStack Nova Network
  • OpenStack Nova API
  • Libvirt and dependant packages

Environment

The following environment has been tested to validate all the procedures described in this document:

  • Management System: both physical or virtual machine
  • OpenStack controller: physical machine
  • OpenStack compute nodes: several physical machines
Note.png
Note
Each physical machine has two NICs, respectively for the public and private networks. That is not required for the Management host.
Important.png
This is important
  • In a production environment we recommend a High Availability solution for the OpenStack Controllers
  • OpenStack modules could be used on virtual machines but we have not tested it yet.
  • One NIC per physical machine with simulated interfaces (VLANs or alias) should work but has not been tested.

Workflow

The goal is to achieve the OpenStack deployment in four steps:

  1. Deploy the system management solution Foreman
  2. Prepare Foreman for OpenStack
  3. Deploy the RHEL core definition with Puppet agent on participating OpenStack nodes
  4. Manage each OpenStack node to be either a Controller or a Compute node

RHEL Core: Common definitions

The Management server itself is based upon the RHEL Core so we define it first.

In the rest of this documentation we assume that every system:

  • Is using the latest Red Hat Enterprise Linux version 6.x. We have tested with RHEL6.4.
  • Be registered and subscribed with an Red Hat account, either RHN Classic or RHSM. We have tested with RHSM.
  • Has been updated with latest packages
  • Has the been configured with the following definitions
Idea.png
This is a tip
IPV6 is not required. Meanwhile for kernel dependencies and performance reasons we recommend to not deactivate the IPV6 module unless you know what you're doing.

NTP

The NTP service is required and included during the deployment of OpenStack components.

Meanwhile for Puppet to work properly with SSL, all the physical machines must have their clock in sync.

Make sure all the hardware clocks are:

  • Using the same time zone
  • On time, with less than 5 minutes delay from each others

Yum Repositories

Activate the following repositories:

  • RHEL6 Server Optional RPMS
  • PuppetLabs
  • EPEL6
rpm -Uvh http://yum.puppetlabs.com/el/6/products/i386/puppetlabs-release-6-7.noarch.rpm
rpm -Uvh http://download.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-8.noarch.rpm
yum-config-manager --enable rhel-6-server-optional-rpms --enable epel --enable puppetlabs-products --enable puppetlabs-deps
yum clean expire-cache

We need the Augeas utility for manipulating configuration files:

yum -y install augeas

SELinux

At the time of writing, SELinux rules have not been fully validated for:

  • Foreman using the automated installation
  • OpenStack

This is an ongoing work.

Note.png
Note
if you plan do to the manual installation of the management server (further down) then you can skip this.

So in the meantime, we need to activate SELinux in permissive mode:

setenforce 0

And make it persistent in /etc/selinux/config file:

SELINUX = permissive
SELINUXTYPE = targeted

FQDN

Make sure every host can resolve the Fully Qualified Domain Name of the management server is defined in available DNS or alternatively use the /etc/hosts file.

Puppet Agent

The puppet agent must be installed on every host and be configured in order to:

  • Point to the Puppet Master which is our Management server
  • Have Puppet plug-ins activated

The following commands make that happen:

PUPPETMASTER="puppet.example.org"
yum install -y puppet

# Set PuppetServer
augtool -s set /files/etc/puppet/puppet.conf/agent/server $PUPPETMASTER

# Puppet Plugins
augtool -s set /files/etc/puppet/puppet.conf/main/pluginsync true

Afterwards, the /etc/puppet/puppet.conf file should look like this:

[main]
# The Puppet log directory.
# The default value is '$vardir/log'.
logdir = /var/log/puppet

# Where Puppet PID files are kept.
# The default value is '$vardir/run'.
rundir = /var/run/puppet

# Where SSL certificates are kept.
# The default value is '$confdir/ssl'.
ssldir = $vardir/ssl

pluginsync=true

[agent]
# The file in which puppetd stores a list of the classes
# associated with the retrieved configuratiion. Can be loaded in
# the separate ``puppet`` executable using the ``--loadclasses``
# option.
# The default value is '$confdir/classes.txt'.
classfile = $vardir/classes.txt

# Where puppetd caches the local configuration. An
# extension indicating the cache format is added automatically.
# The default value is '$confdir/localconfig'.
localconfig = $vardir/localconfig

server=puppet.example.org

Automated Installation of Management Server

Let's get started with the automated deployment of Puppet-Foreman application suite in order to manage our OpenStack infrastructure.

Note.png
Note
The manual installation method is described here: How_to_Deploy_Puppet_Foreman_on_RHEL6_manually

The Automated installation of the Management server provides:

  • Puppet Master
  • HTTP service with Apache SSL and Passenger
  • Foreman Proxy (Smart-proxy) and Foreman
  • No SELinux

Before starting, make sure the "RHEL Core: Common definitions" described earlier have been applied.

In case there are several network interfaces on the Management machine, Foreman HTTPS service is to be activated on the desired interface by either:

  • Deactivate all interfaces but the desired one. Be careful not to cut yourself out!

or

  • After the installation, replace with IP of choice the "<VirtualHost IP:80>" and "<VirtualHost IP:443>" records in the /etc/httpd/conf.d/foreman.conf file

Using Puppet itself onto the Management machine to install the Foreman suite:

# Get packages
yum install -y git 

# Get foreman-installer modules
git clone --recursive https://github.com/theforeman/foreman-installer.git /root/foreman-installer

# Install
puppet apply -v --modulepath=/root/foreman-installer -e "include puppet, puppet::server, passenger, foreman_proxy, foreman"

At this stage, Foreman should be accessible on your Management host on HTTPS: https://host1.example.org. You will be prompted to sign-on: use default user “admin” with the password “changeme”.

Note: If you're using a Firewall you must open HTTPS(443) port to access the GUI.

Optional Database Backend

Please refer to this page if you'd like to use mysql or postgresql as backend for Puppet and Foreman:

How_to_Puppet_Foreman_Mysql_or_Postgresql_on_RHEL6

Foreman Configuration

For OpenStack deployments, we need Foreman to:

  • Setup smart-proxy (Foreman-proxy)
  • Define globals variables
  • Download Puppet Modules
  • Declare hostgroups

Those steps have been scripted using Foreman API.

Note.png
Important
The script must be run (for now) from the Management server itself, as root

Download the script:

git clone https://github.com/gildub/foremanopenstack-setup /tmp/setup-foreman
cd /tmp/setup-foreman

Then edit foreman-params.json file to and change the following to needs:

  • The host section with your foreman hostname and user/passwd if you have changed them
  • The proxy name can be anything you'd like, the host is the same as foreman FQDN name, with ssl and port 8443.
  • The globals are your OpenStack values, adjust all passwords, tokens, network ranges and NICs values to you needs.

Notes: Be careful with JSON syntax - It doesn't like a colon at the wrong place!

Lets launch the script to configure Foreman with our parameters:

./foreman-setup.rb -l logfile all 

Check the log file to confirm there wasn't any error.

Note.png
Note
The above process can also be done manually using Foreman GUI, it's described here: How_to_Deploy_Openstack_Setup_Foreman_on_RHEL6_manually

Manage Hosts

To make a system part of our OpenStack infrastructure we have to:

  • Make sure the host follows the Common Core definitions – See RHEL Core: Common definitions section above
  • Have the host's certificate signed so it's registered with the Management server
  • Assign the host either the openstack-controller or openstack-compute Host Group

Register Host Certificates

Using Autosign

With autosign option, the hosts can be automatically registered and visible from Foreman by adding the hostnames to the /etc/puppet/autosign.conf file.

Signing Certificates

If you're not using the autosign option then you will have to sign the host certificate, using either:

  • Foreman GUI

Get on the Smart Proxies window from the menu "More -> Configuration -> Smart Proxies". And select the "Certificates" from the drop-down button of the smart-proxy you created:

Foreman-proxies.png

From there you can manage all the hosts certificates and get them signed.

  • The Command Line Interface

Assuming the Puppet agent (puppetd) is running on the host, the host certificate would have been created on the Puppet Master and will be waiting to be signed: From the Puppet Master host, use the “puppetca” tool with the command “list” to see the waiting certificates, for example:

# puppetca list
"host3.example.org" (84:AE:80:D2:8C:F5:15:76:0A:1A:4C:19:A9:B6:C1:11)

To sign a certificate, use the “sign” command and provide the hostame, for example:

puppetca sign host3.example.org

Assign a Host Group

Display the hosts using the “Hosts” button at the top Foreman GUI screen.

Then select the corresponding “Edit Host” drop-down button on the right side of the targeted host.

Assign the right environment and attach the appropriate Host Group to that host in order to make it a Controller or a Compute node.

Foreman-host-hostgroup.png

Save by hitting the “Submit” button.

Deploy OpenStack Components

We are done!

The OpenStack components will be installed when the Puppet agent synchronises with the Management server. Effectively, the classes will be applied when the agent retrieves the catalog from the Master and runs it.

You can also manually trigger the agent to check with the puppetmaster, to do so deactivate the agent on the targeted controller node run:

service puppet stop

And run it manually:

puppet agent –verbose --no-daemonize