From Fedora Project Wiki
Line 51: | Line 51: | ||
|| Trimslice Pro/H/H250 ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||N/A ||Tested using USB flash drive. Did not replace running kernel. | || Trimslice Pro/H/H250 ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||N/A ||Tested using USB flash drive. Did not replace running kernel. | ||
|- | |- | ||
|| Highbank ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||N/A ||N/A || | || Highbank ||{{result|pass}} ||{{result|pass}} ||{{result|pass}} ||N/A ||N/A ||System did not fully reboot, needed power reset. | ||
|- | |- | ||
|| Beagleboard XM |||| || || |||| | || Beagleboard XM |||| || || |||| | ||
|} | |} |
Revision as of 15:25, 22 March 2013
Upgrading F17 Images to 3.7 Kernel
F17 GA
Starting with the F17 GA image, yum updated 2013-02-14.
kernel-3.7.3-101.fc17
Hardware | boot | Network | Serial | USB | Display | Final Notes |
---|---|---|---|---|---|---|
Versatile Express (Qemu) | n/a | The install failure resulted on a fully updated F17 system. The boot failure occurred on a F17 GA system, there was no install error, but the kernel did not boot (using qemu-system-arm-1.2.2-6.fc18.x86_64). DTB used for boot test (required). | ||||
Pandaboard | ![]() |
![]() |
![]() |
![]() |
||
Trimslice Bare/Value Pro | ![]() |
Kernel test booted on F18 rootfs successfully. The Trimslice needs a Uboot upgrade to U-Boot 2012.04.01-1.01, a new boot script that changes the load address for the initramfs and a dtb. | ||||
Trimslice Pro/H/H250 | ||||||
Highbank | ||||||
Beagleboard XM | ||||||
Kirkwood | Tested on GuruPlug Server Plus |
kernel-3.7.9-101.fc17
Hardware | boot | Network | Serial | USB | Display | Final Notes |
---|---|---|---|---|---|---|
Versatile Express (Qemu) | ![]() |
Disk Image | n/a | fpaste of boot, using qemu-system-arm-1.2.2-6.fc18.x86_64 with DTB. | ||
Pandaboard | ![]() |
SD | ![]() |
![]() |
![]() |
Boots with no additional configuration. |
Trimslice Bare/Value Pro | ![]() |
SD | ![]() |
![]() |
![]() |
The Trimslice needs a Uboot upgrade to U-Boot 2012.04.01-1.01, a new boot script that changes the load address for the initramfs and a dtb. |
Trimslice Pro/H/H250 | ![]() |
SATA | ![]() |
![]() |
![]() |
The Trimslice needs a Uboot upgrade to U-Boot 2012.04.01-1.01, a new boot script that changes the load address for the initramfs and a dtb. |
Highbank | ![]() |
![]() |
![]() |
![]() |
N/A | Kernel crash after short period of use - Backtrace |
Beagleboard XM |
kernel-3.8.3-102.fc17
Hardware | boot | Network | Serial | USB | Display | Final Notes |
---|---|---|---|---|---|---|
Versatile Express (Qemu) | ![]() |
n/a | Division by zero in kernel on f18 QEMU. | |||
Pandaboard | SD | |||||
Trimslice Bare/Value Pro | ![]() |
![]() |
![]() |
![]() |
N/A | Did not replace running kernel. |
Trimslice Pro/H/H250 | ![]() |
![]() |
![]() |
![]() |
N/A | Tested using USB flash drive. Did not replace running kernel. |
Highbank | ![]() |
![]() |
![]() |
N/A | N/A | System did not fully reboot, needed power reset. |
Beagleboard XM |