From Fedora Project Wiki

< QA‎ | Networking
Revision as of 16:14, 19 October 2015 by Jpopelka (talk | contribs) (Use full stop consistently.)

Operations

A networking client typically connects to a server identified by connection information specified in its configuration or by the user. The general client procedure is to use name resolution service (often through the system C library) and use the result to negotiate a connection through the operating system kernel.

Name resolution phase

Client software retrieves a domain name from the user or from its configuration either as a verbatim value or by parsing a more complex configuration item like an URL or an e-mail address. Client software can often handle special values like literal IP addresses or empty host names. Most often this is the only configuration that is needed. Other name resolution input is built-in but can often also be tweaked by configuration or URL.

Name resolution typically consists of multiple actions. The most typical combination of actions is host name resolution using DNS where A and AAAA are requested separately in order to get IPv4 and IPv6 addresses. Sequential or parallel queries can be used to handle that situation.

See Name resolution for more details.

Example: Jabber (XMPP client connection)

Identifier: user@example.net

Client extracts domain name example.net from the configuration option above, resolves SRV record _xmpp-client._tcp.example.net to get the list of host names and then attempts to resolve A and AAAA records of those host names to get the list of IPv4 and IPv6 addresses to be attempted for connection.

You can use netresolve to mimic the above procedure:

netresolve --node example.net --service xmpp-client --srv --protocol tcp

Connection phase

Connection procedure can start after or during the name resolution phase and uses the name resolution results. The connection procedure can also be fully sequential (client attempts addresses in a given order until a successful connection is established) or using parallelization. The most prominent reason for parallel connection is to avoid waiting for a defunct protocol version by attempting an IPv4 address at the same time as an IPv6 address.

Test cases

Dual-stack to dual-stack

IPv4 connectivity Global or masqueraded
IPv6 connectivity Global

What is tested

  • Whether IPv6 is preferred over IPv4.
  • Whether the component is capable of working over IPv6.
  • Whether sequential or parallel DNS resolution is in use.

Test flow

  1. Let the client connect to a dual-stack server.
  2. Use tcpdump to check all tested properties.

Expected result (sequential, IPv6 preferred)

  • Host requests AAAA record and receives a reply.
  • Host connects via IPv6.
  • No delays, no A query.

Expected result (parallel, IPv6 preferred)

  • Host requests A and AAAA records simultaneously and receives the AAAA reply.
  • Host connects via IPv6.
  • No delays, A reply is ignored if received.

Bad result

Not connecting to IPv6 address or attempting an IPv4 connection.

Dual-stack to dual-stack with lost AAAA answer

Same as above, except that the AAAA answer is lost by a broken DNS server.

IPv4 connectivity Global or masqueraded
IPv6 connectivity Global
Other AAAA request or reply is lost.

What is tested

  • Wheter the component reverts to IPv4 in reasonable time when AAAA answer gets lost.

Test flow

  1. Block IPv6 DNS packets on firewall.
  2. Let the client connect to a dual-stack server.
  3. Use tcpdump to check the communication.
  4. Check the delay.

Expected result (sequential, IPv6 preferred)

  • Host requests AAAA record and gives up after a delay (e.g. 15 seconds).
  • Host requests A record and receives reply.
  • Host connects via IPv4.

Expected result (parallel, IPv6 preferred)

  • Host requests A and AAAA records simultaneously and receives the A reply.
  • Host gives up waiting for AAAA record after a short delay (e.g. 300 milliseconds).
  • Host connects via IPv4.

Bad result (parallel, first result wins)

  • Host requests A and AAAA records simultaneously and receives the A reply.
  • Host connects via IPv4.
  • No delay.

Rationale: IPv6 should be preferred over IPv4 by default.

IPv4 to dual-stack with lost AAAA answer

Same as above, except that the host doesn't have any IPv6 address except link-local and loopback.

IPv4 connectivity Global or masqueraded
IPv6 connectivity Link-local
Other AAAA request or reply is lost.

What is tested

  • Whether the component suppresses AAAA queries when lacking global IPv6 connectivity.

Test flow

  1. Block IPv6 DNS packets on firewall.
  2. Let the client connect to a dual-stack server.
  3. Use tcpdump to check the communication.
  4. Check that there is no delay.

Expected result

  • Host requests A record and receives reply.
  • Host connects via IPv4.
  • No delay, no AAAA query.

Bad result

  • Host requests A and AAAA record and receives A reply.
  • Host gives up waiting for AAAA reply.
  • Host connects via IPv4 after an excessive delay.

Rationale: IPv4-only host should connect to IPv4 address without delay.

Dual-stack to dual-stack with lost IPv6 communication

IPv4 connectivity Global or masqueraded
IPv6 connectivity Global but packets to destination get dropped
Other Lost client-server IPv6 communication.

What is tested

  • Whether the component reverts to IPv4 in reasonable time when local or remote network drops all IPv6 communication.

Test flow

  1. Let the client connect to a dual-stack server with lost IPv6 communication.
  2. Use tcpdump to check communication.
  3. Check the delay.

Expected result (sequential, IPv6 preferred)

  • Host requests AAAA record and receives reply.
  • Host attempts connecting to IPv6 and times out.
  • Host requests A record and receives reply.
  • Host connects via IPv4

Expected result (parallel DNS, IPv6 preferred)

  • Host requests A and AAAA records simultaneously and waits for AAAA reply.
  • Host attempts connecting to IPv6 and times out, receiving A reply in the meantime.
  • Host connects via IPv4.

Expected result (parallel DNS, parallel TCP, IPv6 preferred)

  • Host requests A and AAAA records simultaneously.
  • Host attempts IPv4 and IPv6 connections upon receiving the respective records.
  • IPv4 connection is established.
  • IPv6 connection is given up after a short delay (e.g. 300 milliseconds).
  • IPv4 connection is used.

Notes

There is no common bad result. But the sequential connection is highly suboptimal and therefore is not suitable for interactive applications.