From Fedora Project Wiki
Line 62: Line 62:


# fix the rootfs mount point
# fix the rootfs mount point
sed -e "s|.* / \(ext4.*\)$|UUID=${UUID}  \1|" /tmp/rootfs/etc/fstab
sed -ie "s|.* / \(ext4.*\)$|UUID=${UUID}  \1|" /tmp/rootfs/etc/fstab
sync
sync



Revision as of 17:58, 3 June 2013

Fedora 19 ARM Beta

The Fedora ARM team is pleased to announce the Fedora 19 Beta for ARM is now available for download from:

https://dl.fedoraproject.org/pub/fedora-secondary/releases/test/19-Beta/Images/armhfp/

This marks the last significant milestone before reaching the final release of Fedora 19 for ARM, with only critical bug fixes being added as updates to make this our most solid release to date.

The Fedora 19 Beta for ARM includes two pre-built images - one for the Pandaboard and Pandaboard ES which requires special partitioning, the second will support the Trimslice and Versatile Express(QEMU). The Beta for ARM also includes an installation tree in the yum repository which may be used to PXE-boot a kickstart-based installation on systems that support this option, such as the Calxeda EnergyCore (HighBank).

For the Trimslice

Warning.png
IMPORTANT
You must use a Device Tree enabled Uboot to boot the Fedora 19 Trimslice image. Failure to do so will result in a non-booting system.

Download the image for use in the Trimslice:

wget http://dl.fedoraproject.org/pub/fedora-secondary/releases/test/19-Beta/Images/armhfp/Fedora-armhfp-19-Beta-1-sda.raw.xz

Copy the image to the intended media:

xzcat Fedora-armhfp-19-Beta-1-sda.raw.xz > /dev/<location-of-your-media> 

Insert into the Trimslice and boot. There is no root password required initially - this something you should change right away.

Once the system is booted it is recommended to do a little clean up and remove the unneeded kernels:

yum remove kernel kernel-lpae

For the Pandaboard and Pandaboard ES

Download the image for use with the Pandaboard or Pandaboard ES.

wget http://dl.fedoraproject.org/pub/fedora-secondary/releases/test/19-Beta/Images/armhfp/Fedora-OMAP-armhfp-19-Beta-1-sda.raw.xz

As root copy the image to the intended media:

xzcat Fedora-OMAP-armhfp-19-Beta-1-sda.raw.xz > /dev/<location-of-your-media>

Before Booting the OMAP Image

Before booting the OMAP image reinsert the media into a host pc. The image should automatically mount, however if it does not you may need to adjust the mount point used in the below example. Use the 'mount' command to determine the name of the partition you will be working with.

DEVICE=/dev/<device>  # use the mount command to determine the device, omit any tailing partitions (for example : /dev/sdb or /dev/mmcblk0)
TARGET=               #this is your target device - panda, panda_es 


# fix the boot partition
umount ${DEVICE}*1
mkfs.vfat -n 'BOOT' ${DEVICE}*1


# generate a new UUID for later use on the rootfs.
UUID=$(uuidgen)


# fix the rootfs
umount ${DEVICE}*3
tune2fs -L 'rootfs' -U "$UUID" ${DEVICE}*3


# Create temporary mount points
mkdir /tmp/{uboot,rootfs}
sudo mount ${DEVICE}*1 /tmp/uboot
sudo mount ${DEVICE}*3 /tmp/rootfs


# copy over the TI boards boot files.
sudo cp /tmp/rootfs/usr/share/uboot-panda/MLO u-boot.img uEnv.txt.$TARGET /tmp/uboot/
sync


# fix the rootfs mount point
sed -ie "s|.* / \(ext4.*\)$|UUID=${UUID}  \1|" /tmp/rootfs/etc/fstab
sync

umount /tmp/rootfs
umount /tmp/uboot/

#THE END

For Versatile Express Emulation with QEMU

Even without hardware its possible to run the Fedora 19 ARM Beta using QEMU. To this we will use the generic image.

wget http://dl.fedoraproject.org/pub/fedora-secondary/releases/test/19-Beta/Images/armhfp/Fedora-armhfp-19-Beta-1-sda.raw.xz

Extract the image:

unxz Fedora-armhfp-19-Beta-1-sda.raw.xz

Mount the image and extract the kernel and initramfs for use with booting.

sudo kpartx -av Fedora-armhfp-19-Beta-1-sda.raw

Make a temporary mount point

mkdir /tmp/boot
sudo mount /dev/mapper/loop0p1 /tmp/boot
sudo cp /tmp/boot/initramfs-3.9.2-301.fc19.armv7hl.img .
sudo cp /tmp/boot/vmlinuz-3.9.2-301.fc19.armv7hl .
sudo cp -r /tmp/boot/dtb-3.9.2-301.fc19.armv7hl .

To boot:

sudo qemu-system-arm -machine vexpress-a9 -m 1024 -nographic -net nic -net user \
 -append "console=ttyAMA0,115200n8 rw root=/dev/mmcblk0p3 rootwait physmap.enabled=0" \
 -kernel vmlinuz-3.9.2-301.fc19.armv7hl \
 -initrd initramfs-3.9.2-301.fc19.armv7hl.img \
 -sd Fedora-armhfp-19-Beta-1-sda.raw \
 --dtb dtb-3.9.2-301.fc19.armv7hl/vexpress-v2p-ca9.dtb

For convenience you can also download a script for booting the system here. To run the script:

chmod 755 boot-vexpress
./boot-vexpress -h
Usage: ./boot-vexpress [--gui] --kernel=vmlinuz... --ramfs=initramfs --image=fsimage [--dtb=vexpress.dtb]

To boot the image:

sudo ./boot-vexpress --kernel=vmlinuz-3.9.2-301.fc19.armv7hl --ramfs=initramfs-3.9.2-301.fc19.armv7hl.img --image=Fedora-armhfp-19-Beta-1-sda.raw --dtb=dtb-3.9.2-301.fc19.armv7hlvexpress-v2p-ca9.dtb

Calxeda EnergyCore (HighBank)

The Fedora 19 Beta for ARM includes support for systems that are able to perform a network installation using a kickstart, including enterprise hardware such as the Highbank. A working kickstart can be found here.

For more detailed instructions on setting this up, please visit this page.

Known Issues

  • Significant logical volume noise on first boot. This is harmless and resolved after rebooting the system.
  • Initial setup is not run on first boot.