- 1 Introduction
- 2 What's In the Usability Lab?
- 2.1 Compartment 1: DVR + mic wire, monitor cable
- 2.2 Compartment 2: 3 camera power supplies, 3 camera stands
- 2.3 Compartment 3: 3 cameras
- 2.4 Compartment 4: Scan converter
- 2.5 Compartment 5: Microphone, microphone plate, and scan converter power cable
- 2.6 Compartment 6: Camera cables, scan converter video cable, DVR power supply, DVR remote
So, you've somehow acquired the Fedora Usability Lab. Perhaps you've volunteered to run some usability tests at an event or show, or perhaps you got a group of friends together to test out some software you've been working on in Fedora. Great! But, what next?
- First, let's review what equipment the Fedora Usability lab will provide you.
- After that, we'll review what equipment you'll need to supplement the kit with in order to run a successful usability test.
- Finally, we'll walk through how to assemble the usability lab.
By the time you follow the steps in this document, you'll have configured all the equipment you need to run a usability test.
What's In the Usability Lab?
The Fedora Usability Lab comes in a big black box. The box it comes in is a hard-sided Opteka equipment case with foam padding on the inside to protect the parts. The box is 13" x 18" x 7", and it has a shoulder strap and briefcase-style carrying handle.
Go ahead and open up the box. There are six compartments inside the usability lab box. You'll see them labeled below. Let's review the equipment in each compartment.
Compartment 1: DVR + mic wire, monitor cable
DVR + mic wire
The DVR is the central unit that mixes video from the 3 cameras and from the test computer (via the scan converter) and records them into video files. It also mixes the audio. The mic wire attached to the unit is used for connecting the microphone.
The monitor cable included in this kit is intended for you to connect the computer you are running the usability test on to the scan converter box. This will enable the DVR to record video of what is happening on-screen as the user runs through a usability test. Since the video of the screen is recorded externally, your usability testers will not experience any lag or delay on the system due to recording.
The monitor cable will connect to the video out monitor port of a computer on one end, and the video in port on the narrow end of the scan converter on the other end. Typically we use laptops or netbooks for testing. Remember that the Fedora Usability Lab does not come with a computer for testing on - you will have to provide this.
Compartment 2: 3 camera power supplies, 3 camera stands
3 Camera power supplies and 3 camera stands
You'll see the three camera power supplies in the top row of the photo above, the three circular metal camera stands in the bottom row. The power supplies plug into the end of the cables coming out of the cameras. The cameras turn on as soon as they are plugged into these power supplies and the power supplies are plugged into a power source.
The circular metal camera stands screw into a small screw hole on the end of each camera cylinder, opposite the lens. The camera stands have a screw that allows you to adjust then tighten the angle the camera points out. Note that the camera stands are light and typically require a book or some other weight to hold them down. Yes, this is annoying. :)
Compartment 3: 3 cameras
Each camera comes with a bubblewrap pouch to keep them protected when stored. They are packed into the case rolled up in the bubble wrap pouch. When you unpack the lab, please be sure not to lose the bubblewrap camera pouches.
The cameras are cylindrical, with a lens at one end and a wire and screwhole for a stand on the other end. So you are able to set the cameras up in order to take an upright image, the top of the camera has been marked with white markings. (One has a line, two have silly faces. :) )
Compartment 4: Scan converter
The scan converter essentially takes a video signal from the computer you're testing on, and feeds that signal into the DVR so it can be recorded. Note in the photo above that the scan converter has two monitor cable ports. You will not be using the one on the longer side (to the left in the picture.) That's an output port. Rather, you'll be using the monitor port on the right side of the photo (input port), on the narrow end of the scan converter box.