|Line 80:||Line 80:|
Example 4: IPv6 connections from 1:2:3:4:6:: to service radius at a rate of 3 per minute
Revision as of 13:35, 20 March 2013
firewalld Rich Language
This feature adds a rich (high level) language to firewalld, that allows to easily create complex firewall rules without the knowledge of iptables syntax.
- Name: Thomas Woerner
- Email: email@example.com
- Targeted release: Fedora 19
- Last updated: 2013-03-20
- Percentage of completion: 80%
- The feature is limited to milestone 1 (base): configuration with files, no cli and no D-Bus interface
- Firewalld milestones for rich language and lockdown features, the milestones 1 and 2 (base and cli) a planned for F-19. Milestone 3 (gui) is planned for F-20.
- Milestone 1: Rich config language via config files; minimal lockdown ~ end of March
- Milestone 2: New config language via D-BUS interfaces with command line client ~ end of May
- Milestone 3: GUI early to mid July
Currently, complex firewall rules can only be added using the direct interface of firewalld. But this requires to know the syntax of iptables and the rules are not permanent.
With the rich language more complex firewall rules can be created in an easy to understand way. The language will use keywords with (sometimes multiple) values and will be an abstract representation of ip*tables and ebtables rules. Services and zones can be configured using this language, the current configuration will still be supported.
A mixture of the old and new configuration of services and zones might be possible, but this needs to be verified. With the possibility to use the rich language in services and zones, the configuration will also be permanent.
The configuration with files will be available for Fedora 19. The D-BUS interface with the command line client should be finished, but this depends on Fedora 19 schedule. UI work will most likely be available later (depends on Fedora 19 schedule also).
Benefit to Fedora
More powerful and easier firewall configuration.
Only needs changes in firewalld and it's components.
How To Test
Create firewall rules using the rich language in services and zones. More to come.
Users will be able to easily create more powerful and also permanent firewall configurations.
Disabling or reverting of the feature should be easy as it will be created as an addition to the current configuration. Only users of the new language will be affected.
The rich language extends the currect zone elements (service, port, icmp-block, masquerade and forward-port) with additional source and destination addresses, logging, actions and limits for logs and actions.
The use of destination addresses is not possible with all elements. This depends on the use of destination addresses for example in services.
Logging can be done with with the LOG and also with the AUDIT target. A new chain is added to all zones: <zone>_log. This will be jumped into before the deny chain to be able to have a proper ordering.
Example 1: Enable new IPv4 and IPv6 connections for protocol 'ah'
<rule> <protocol value="ah"/> <accept/> </rule>
Example 2: Allow new IPv4 and IPv6 connections for service ftp and log 1 per minute using audit
<rule> <service name="ftp"/> <audit type="ACCEPT"> <limit value="1/m"/> </audit> <accept/> </rule>
Example 3: Allow new IPv4 connections from address 192.168.0.0/24 for service tftp and log 1 per minutes using syslog
<rule family="ipv4"> <source address="192.168.0.0/24"/> <service name="tftp"/> <log prefix="tftp" level="info"> <limit value="1/m"/> </log> <accept/> </rule>
Example 4: New IPv6 connections from 1:2:3:4:6:: to service radius are rejected and logged at a rate of 3 per minute
<rule family="ipv6"> <source address="1:2:3:4:6::"/> <service name="radius"/> <log prefix="dns" level="info"> <limit value="3/m"/> </log> <reject/> </rule>
Example 5: Forward IPv6 port/packets receiving from 1:2:3:4:6:: on port 4011 with protocol tcp to 1::2:3:4:7 on port 4012
<rule family="ipv6"> <source address="1:2:3:4:6::"/> <forward-port to-addr="1::2:3:4:7" to-port="4012" protocol="tcp" port="4011"/> </rule>
Fedora 19 includes the latest firewalld version that supports a rich language to be able to create more complex firewalls in a easy way.