From Fedora Project Wiki

Note.png
Associated release criterion
This test case is associated with the Basic_Release_Criteria#freeipa-server-requirements release criterion. If you are doing release validation testing, a failure of this test case may be a breach of that release criterion. If so, please file a bug and nominate it as blocking the appropriate milestone, using the blocker bug nomination page.


Description

Test that the IPA server can be installed

Setup

  1. For testing purposes, a machine (or VM) with 1GB of RAM and 4 GB of free disk space for binaries, data and logs should be plenty to set up and run an IPA master.
  2. Make sure /etc/hosts is sane and your hostname does not appear in either the IPv4 or IPv6 localhost lines.
  3. In the following text, we assume that the IPA server name is srv.ipa.example.org and the realm is IPA.EXAMPLE.ORG
  4. If you have an existing AD server in your network, choose a different name for the IPA server realm name. Clients that use DNS autodiscovery to find the KDC to use may get confused and try to authenticate to the AD KDC. It is recommended that FreeIPA and AD serves different domains, for example ipa.example.org and ad.example.org

How to test

Installation

First, install the FreeIPA server package:

# yum install freeipa-server

With DNS

We highly recommend installing FreeIPA with integrated DNS service as it will make client autodiscovery or AD Trust configuration much easier. You will just need to make sure that the domain managed by FreeIPA is properly delegated to the FreeIPA server or that your VMs are configured to use FreeIPA server directly (by configuring your DHCP server or manually updating /etc/resolv.conf).

# yum install bind bind-dyndb-ldap
# ipa-server-install --setup-dns

Or with all options on the command-line:

# ipa-server-install -a Secret123 -p Secret123 --domain=ipa.example.org --realm=IPA.EXAMPLE.ORG --hostname srv.ipa.example.org --setup-dns --forwarder=<forwarder IP> -U

Substitute you existing DNS server's IP for <forwarder IP>, or pass --no-forwarders.

Without DNS

For a fully-interactive install run:

# ipa-server-install

You can optionally provide all options on the command-line:

# ipa-server-install -a Secret123 -p Secret123 --domain=ipa.example.org --realm=IPA.EXAMPLE.ORG --hostname srv.ipa.example.org -U

Verify the basics

Ideally each of these installation steps will finish with no errors and will yield a running set of IPA services.

To briefly test the installation:

# kinit admin  # (the password is the admin password, or the password from -a)

Show our own user entry:

# ipa user-show admin

And make sure nss can see us too:

# id admin
# getent passwd admin

Verify the server_mode

Starting with version 3.3, the SSSD running on the server operates in a special mode, denoted with ipa_server_mode directive set in the config file. Verify it has been set:

# grep server_mode /etc/sssd/sssd.conf 
ipa_server_mode = True

Verify DNS

Verify these only if you installed with a DNS server.

# dig srv.ipa.example.org.

Look for a line like this in the output:

srv.ipa.example.org.      86400   IN      A       192.168.0.1
# host srv.ipa.example.org
srv.ipa.example.org has address 192.168.0.1
# ipa dns-resolve srv.ipa.example.org
---------------------------
Found 'srv.ipa.example.org.'
---------------------------
# ipa host-show srv.ipa.example.org
  Host name: srv.ipa.example.org
  Principal name: host/srv.ipa.example.org@IPA.EXAMPLE.ORG
  Keytab: True
  Managed by: srv.ipa.example.org

Configure the Firewall

To open all ports typically required for FreeIPA using firewalld, run these commands:

# for i in freeipa-ldap freeipa-ldaps dns; do firewall-cmd --permanent --add-service $i; done
# systemctl restart firewalld.service

Further tests

After completing this test it would be a good idea, if you have extra test systems, to test installing a replica server and installing clients via the realm CLI, kickstart and/or cockpit.

Expected Results

All the test steps should end with the specified results.