From Fedora Project Wiki
m (Testing Results)
 
Line 111: Line 111:
run bootcmd</pre>
run bootcmd</pre>
==[[Talk:Architectures/ARM/TrimSlicePRO|Testing Results]]==
==[[Talk:Architectures/ARM/TrimSlicePRO|Testing Results]]==
*Boot from a SanDisk Ultra 64 GB SDXC Card

Latest revision as of 11:44, 14 June 2012

This page is a draft only
It is still under construction and content may change. Do not rely on the information on this page.

How to install Fedora on TrimSlice PRO

The TrimSlice PRO developer kit comes delivered with a 32GB SSD containing another Linux distribution, but can boot from pretty much any media (SD. USB, MicroSD, SSD) and you are free to experiment without voiding warranty.

U-Boot is factory preprogrammed in internal flash. There is no need to reflash U-Boot as the default U-Boot version is very open and friendly configured. But you may do so if you wish, following instructions from TrimSlice. One very nice thing is that the device allows easy recovery using the SD slot if the boot flash gets corrupted, eleminating the need for JTAG in such cases.

Kernel & Initrd

The kernel & initrd needs to be converted to U-Boot images. This is done by running

mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n 2.6.40.3-0.fc15.armv7hl -d ../boot/vmlinuz-2.6.40.3-0.fc15.armv7hl.tegra uImage

mkimage -A arm -O linux -T ramdisk -C none -n 2.6.40.3-0.fc15.armv7hl -d ../boot/initramfs-2.6.40.3-0.fc15.armv7hl.tegra.img uInitrd

U-Boot behavior

The TrimSlice U-Boot automatically tries to boot from the first partition of any of the above boot sources and expects a boot.scr u-boot script file in / or /boot on the boot device.

When starting boot.scr the following variables are set for convenience

 fs         filesystem type (ext2 or fat)
 interface  u-boot interface type (mmc or usb)
 bus        bus number of the interface
 prefix     boot prefix (/ or /boot)

enabling a generic boot.scr script to be used to boot from any of the possible boot devices. (see below)

Fedora boot script

Save this as boot.cmd in /boot and convert it to a uboot image by using

mkimage -A arm -O linux -T script -C none -d boot.cmd boot.scr

echo starting Fedora boot.scr

printenv

if test -z "${fs}" -o -z "${interface}" -o -z "${device}"; then
	echo Missing system parameters
	exit 1
fi

if ${fs}load ${interface} ${device}${bootpart} ${loadaddr} kernel.scr; then
	source ${loadaddr}
fi

if test -z "${rootpart}" -a -z "${rootuuid}" -a 1 = 1 ; then
	echo Using default rootpart 4
	setenv rootpart 4
	#setenv rootuuid 3e6be9de-8139-11d1-9106-a43f08d823a6
fi

#if test -z "${kernel}" -a -z "${kernelver}"; then
#	setenv kernelver 2.6.40.3-0.fc15.armv7hl.tegra
#fi
if test -z "${kernel}" -a 1 = 1 ; then
	echo "Using default image names"
	setenv kernel uImage
	setenv initrd uInitrd
fi
if test -n "${kernelver}"; then
	setenv kernel ${kernel}-${kernelver}
	setenv initrd ${initrd}-${kernelver}
fi

if test -z "${console}" -a 1 = 1 ; then
	setenv console ttyS0,115200n8
fi

setenv initrdaddr 1600000

echo Parameters set

printenv

if test -n "${rootuuid}"; then
	echo booting with UUID selected root
	setenv rootfs ro root=UUID=${rootuuid}
elif test "${interface}" = "mmc" && test "${bus}" = "1"; then
	echo booting from internal microSD
	setenv rootfs ro root=/dev/mmcblk0p${rootpart}
elif test "${interface}" = "mmc" && test "${bus}" = "0"; then
	echo booting from external SD
	if mmc init 1; then
		setenv rootfs ro root=/dev/mmcblk1p${rootpart}
	else		
		setenv rootfs ro root=/dev/mmcblk0p${rootpart}
	fi
	mmc init 0

elif test "${interface}" = "usb" && test "${bus}" = "1"; then
	echo booting from internal SSD
	setenv rootfs ro root=/dev/sda${rootpart} nohdparm rootwait
else
	echo booting from external USB
	setenv rootfs ro root=/dev/sdb${rootpart} rootwait
fi

setenv bootargs console=${console} ${rootfs}
setenv load_kernel ${fs}load ${interface} ${device}${bootpart} ${loadaddr} ${prefix}${kernel}
setenv load_initrd ${fs}load ${interface} ${device}${bootpart} ${initrdaddr} ${prefix}${initrd}
setenv bootcmd bootm ${loadaddr} ${initrdaddr}

echo bootargs ${bootargs}
echo kernel ${load_kernel}
echo initrd ${load_initrd}
echo ${bootcmd}

run load_kernel
run load_initrd
run bootcmd

Testing Results

  • Boot from a SanDisk Ultra 64 GB SDXC Card