- 1 Power Management improvements
- 1.1 Summary
- 1.2 Owner
- 1.3 Current status
- 1.4 Detailed Description
- 1.5 Benefit to Fedora
- 1.6 Scope
- 1.7 Test Plan
- 1.8 User Experience
- 1.9 Dependencies
- 1.10 Contingency Plan
- 1.11 Documentation
- 1.12 Release Notes
Power Management improvements
Improve the current state of power management, especially in regard to userland.
- Phil Knirsch (Lead, tuned, documentation)
- Jiri Skala (BLTK packager)
- Marcela Maslanova (initscript/udev service start/stop automation)
- Targeted release: [Fedora 11]
- Last updated: (02/02/09)
- Percentage of completion: 15%
Power management and power saving in Fedora has been a topic is special areas over the last few releases. Using powertop especially for Fedora 9 quite a few improvements were already done, but there is still lots of things that haven't been touched in regard to power saving.
Benefit to Fedora
Simple: On average use less power for turned on machines while not affecting user experience (a lot ;)).
- Review and fix behaviour of typical applications in a full installed Fedora in regard to:
- CPU wakeups
- Disk IO
- Network IO
- Add a workload measurement package to Fedora (BLTK adapted to Fedora use case)
- Enable relatime for filesystem by default during installation
- Write a monitoring and tuning daemon that adapts system settings to the current use
- Review services and make a framework that will allow services to start depending on installed hardware or software
- Provide scripts and documentation to perform an individual review of a system and tips & tricks on how to improve it
- Run Fedora 10 and, measure the the power usage for 1 day
- Run Fedora 11 on the same hardware and compare the power usage over 1 day with Fedora 10
As power saving is not really visible without a measuring it the effects will not be directly visible. So in order to really see the effect you'll either need a laptop and run that on battery power or a wattmeter that is hooked between your system and the power line.
- Anaconda changes (for relatime)
- Fixes need to get included to have an effect (really ;)).
Make sure none of the more aggressive power saving features breaks on common hardware and back it out it case it does.
Simple user tips for improving power usage
- Enforce turning of machines that are not used (e.g. company policy)
- Turn of unused hardware already in BIOS.
- Disable power hungry features.
- Enable CPU scaling if supported for ondemand CPU governor. DONT use powersave governor, typically uses more power than ondemand
(race to idle).
- Put network card to 100 mbit/10 mbit:
- 10 mbit: ethtool -s eth0 advertise 0x002
- 100 mbit: ethtool -s eth0 advertise 0x008
- Doesn't work for every card
- Put harddisk to spindown fast and full power saving:
- hdparm -S240 /dev/sda (20m idle to spindown)
- hdparm -B1 /dev/sda (Max powersave mode)
- Make sure writes to hd don't wake it up too quickly:
- Set flusing to once every hour
- echo "360000" > /proc/sys/vm/dirty_writeback_centisecs
- Enable laptop mode
- echo "1" > /proc/sys/vm/laptop_mode
- Enable USB autosuspend by adding the following to the kernel boot commandline:
- Screensaver needs to dpms off the screen, not just make colors black. To turn of monitor after 120s when X is running:
- xset dpms 0 0 120
Simple programmer tips for improving power usage
- Wake up only when necessary
- No poll() calls
- If you wake up, do everything at once (race to idle)
- Use large buffers to avoid frequent disk access. Write one large block at a time
- Don't use [f]sync() if not necessary
- Group timers accross applications if possible (even systems)
Users of Fedora 11 should be able to see some reduction in power usage of their systems.